COB
COB
STR-C-COB-SW-2W
COB Strip-to-Wire Connector | 8mm LED Strips | 72W Max
Links an 8mm COB LED strip directly to a power source or wiring run. The clamp mechanism grips the tape light and exposes the metal contacts without soldering. Rated up to 72W with 12-24V input. Built with durable plastic and brass contacts. Suitable for dry locations.
Key Specs:
Compatible: 8mm COB LED strips
Max load: 72W
Input: 12-24Vdc
Pins: 2-wire
Dry locations only
COB
COB
STR-C-COB-SS-L-STR
COB 90-Degree Connector | 8mm LED Strips | 72W Max
Joins two 8mm COB LED strips at a right angle without bending or stressing the strip. Ideal for corner installations and angled layouts. Rated up to 72W with 12-24V input. Durable plastic body with brass contacts. Dry locations only.
Key Specs:
Compatible: 8mm COB LED strips
Connection angle: 90 degrees
Max load: 72W
Input: 12-24Vdc
Dry locations only
COB
COB
STR-C-COB-SS-STR
COB Strip-to-Strip Straight Connector | 8mm LED Strips | 72W Max
Joins two 8mm COB LED strips end-to-end in a straight line for seamless light flow without gaps or interruptions. Rated up to 72W with 12-24V input. Durable plastic body with brass contacts. Dry locations only.
Key Specs:
Compatible: 8mm COB LED strips
Connection type: straight / end-to-end
Max load: 72W
Input: 12-24Vdc
Pins: 2-wire
Dry locations only
COB
COB
STR-C-COB-SS-FLX
COB Strip-to-Strip Flexible Connector | 8mm LED Strips | 72W Max
Connects two 8mm COB LED strips with a short wire bridge, allowing flexible routing around corners and angles without bending or stressing the strips. Rated up to 72W with 12-24V input. Durable plastic and brass contacts. Dry locations only.
Key Specs:
Compatible: 8mm COB LED strips
Connection type: flexible / bridged
Max load: 72W
Input: 12-24Vdc
Pins: 2-wire
Dry locations only
RGB COB
RGB COB
STR-C-COB-RGB-SW-2W
RGB COB Strip-to-Wire Connector Kit | 10mm LED Strips
Cutting a pre-wired roll to length leaves one piece without leads. This solderless kit fixes that: it lands a cut 10 mm, 4-pin RGB COB section on a pre-wired 7 in lead, so the offcut becomes a second, independent run fed from the controller. The kit includes a connection platform, an end cap that locks the strip in place, and the strip-to-wire connector, all matched to Arani's 24V RGB COB strip. All four conductors land in a single clamp, with no splice to tape up or troubleshoot later. One roll can now cover two separate zones, and nothing ends up in the bin.
RGB COB
RGB COB
STR-C-4PIN-RGB
RGB COB Strip-to-Strip Connector Kit | 10mm LED Strips
A pre-wired 16 ft roll covers most jobs, but not every run lands on a roll length. This solderless kit joins two 10 mm, 4-pin RGB COB segments end to end, so you can add an offcut or a second cut section and extend the run exactly where the layout needs it. Two end caps lock each strip onto a shared connection platform, keeping all four channels aligned so colour stays consistent across the joint. Cut at any 2 in mark, clamp, and keep going, with no soldering on site. Matched to Arani's 24V RGB COB strip, it turns leftover tape into usable run length instead of scrap.
8mm | 3528
8mm | 3528
STR-C-3528-SW-2W
3528 Strip-to-Wire Connector | 8mm LED Strips
Links an 8mm 3528 LED strip directly to a driver, power supply, or wiring run. The clamp mechanism holds the strip securely while exposing the metal contacts for easy wire attachment without soldering. Compatible with 8mm wide LED strips. Key Specs: - Compatible: 8mm LED strips (3528 series) - Connection type: strip-to-wire - Pins: 2-wire - No soldering required
8mm | 3528
8mm | 3528
STR-C-3528-SS-L-FLX
3528 90-Degree Connector | Strip to Strip | Flexible | 8mm
Joins two 8mm 3528 LED strips at a right angle without bending or stressing the strip. Ideal for corner installations and angled layouts. Sturdy plastic and brass construction ensures reliable connections. No soldering required. Key Specs: - Compatible: 8mm LED strips (3528 series) - Connection angle: 90 degrees - Connection type: flexible / bridged - No soldering required