The page your are looking for doesn't exists
× Checkout our new products belowLED Lighting
24V Non-Dimmable Plug-in LED Driver | 30W | Black | Class 2 | Level VI
Power a 24V LED tape or puck light run straight from a wall outlet, with no hardwiring and no junction box. This 30W driver takes a universal 100-240Vac input and holds a steady 24Vdc output up to 1.25A, a good fit for short cabinet, shelf and display runs. It is cULus listed, Class 2 and DOE Level VI efficient, and ships with a 4 ft detachable AC cord and 4 ft DC leads, ready to plug in.
24V Non-Dimmable Plug-in LED Driver | 60W | Black | Class 2 | Level VI
Power a 24V LED tape or puck light run straight from a wall outlet, with no hardwiring and no junction box. This 60W driver takes a universal 100-240Vac input and holds a steady 24Vdc output up to 2.5A, enough for longer under-cabinet runs or several puck lights on one driver. It is cULus listed, Class 2 and DOE Level VI efficient, and ships with a 4 ft detachable AC cord and 4 ft DC leads, ready to plug in.
12V DC Electronic Transformer (60W) Hard Wire With Junction Box V3
Built to Class 2 and Type HL standards and cULus listed for dry, damp, and wet locations, this 60W hardwire driver is engineered for commercial and industrial LED installations where protection and reliability are non-negotiable. All five dimming protocols — TRIAC, 0-10V, 1-10V, PWM, and RX — are supported on a single unit, so there is no need to stock separate drivers for different control systems on the same project. A full-protection aluminum enclosure with SCP, OVP, OTP, and OLP guards the load from fault conditions, with automatic hiccup recovery that self-resets without a service call. At 12Vdc and 5A continuous output, this driver is sized for compact constant-voltage strip and fixture runs up to 60W, backed by a three-year warranty.
24V DC Electronic Transformer (60W) Hard Wire With Junction Box V3
Built to Class 2 and Type HL standards and cULus listed for dry, damp, and wet locations, this 60W hardwire driver covers 24Vdc constant-voltage installations with full five-protocol dimming support — TRIAC, 0-10V, 1-10V, PWM, and RX — in a single unit. The full-protection aluminum enclosure includes SCP, OVP, OTP, and OLP with automatic hiccup recovery, so the driver self-resets after a fault rather than requiring on-site service. At 24Vdc/2.5A, it is optimally sized for mid-run commercial strip installations on 24V systems — the preferred voltage for longer LED tape runs where voltage drop is a concern. Backed by a three-year warranty and rated for any location type.
24V DC Electronic Transformer (96W) Hard Wire With Junction Box V3
Stepping up to 96W while maintaining a Class 2 Type HL listing, this 24Vdc hardwire driver handles larger architectural LED installations that a 60W unit cannot cover — without requiring a Class 1 installation approach. At 91% efficiency and a power factor of ≥0.95, it runs cool and draws cleanly from the 100–277Vac supply, with all five dimming modes — TRIAC, 0-10V, 1-10V, PWM, and RX — already on board. The full-protection aluminum case with automatic hiccup recovery and 8 half-inch knockouts adapts to most enclosure and conduit configurations on commercial jobsites. cULus listed, RoHS and SELV compliant, backed by a three-year warranty.
12V DC Electronic Transformer (120W) Hard Wire With Junction Box V3
Delivering 120W through two independent 12Vdc/5A outputs while holding a Class 2 Type HL listing, this hardwire driver is built for larger 12V installations — display cases, architectural coves, or multi-zone strip layouts — where high wattage and code-compliant Class 2 wiring are both required. Five-in-1 dimming (TRIAC, 0-10V, 1-10V, PWM, RX) covers every common control scenario, and the full-protection aluminum enclosure with eight half-inch knockouts, SCP, OVP, OTP, and OLP integrates cleanly into standard commercial electrical enclosures. At 90.5% efficiency and ≥0.95 power factor, it draws less than 1.3A from a 120Vac branch circuit at full load. cULus E362082 listed, three-year warranty.
24V DC Electronic Transformer (192W) Hard Wire With Junction Box V3
At the top of the hardwire driver range at 192W, this unit delivers two independent 24Vdc/4A outputs from a single Class 2 Type HL listed enclosure — making it the go-to choice for large-scale architectural strip installations, signage, or multi-zone commercial lighting where maximum run length and load capacity are the priority. At 92% efficiency it produces the least heat per watt in the lineup, and the ≥0.95 power factor keeps the upstream circuit clean. All five dimming protocols are built in, and the full-protection aluminum enclosure with ten half-inch knockouts and automatic hiccup recovery handles any fault condition without manual intervention. cULus E362082 listed, RoHS and SELV compliant, three-year warranty.
Track Light LED Head | 15W | 5CCT | Adjustable Beam | Black | V1
The TL-15W-VAR-BK-AD-V1 is a premium LED track head designed for ultimate flexibility in directional lighting. With a 15W output equivalent to 90W halogen, it delivers up to 1,150 lumens with an adjustable beam angle of 20° to 50°, making it ideal for accent or general lighting. Users can select from five color temperatures (2700K to 5000K) via integrated CCT tuning. The fixture offers high color rendering (CRI >90), low glare (UGR 0.9.
4FT Track | Black | V1
Add versatility to your lighting projects with Arani's 4-foot LED track TL-4FT-BK-V1 — a durable and stylish solution designed for track installations. Its aluminum housing and slim profile blend seamlessly into both residential and commercial spaces. Compatible with HALO connectors, this track provides safe 120 V power, with a maximum current capacity of 16 A and a total power of 1,920 W. The product comes with finishing end caps installed on both ends, ensuring a clean and professional appearance.
Slim Panel 4" | RGBW | 600 Lumens | Round | White | V4
Colour-changing recessed lighting that the homeowner controls from their phone, with nothing extra for you to wire in. This 4-inch slim panel pairs with the Smart Life app, Google Home or Amazon Alexa and delivers 16 million colours, tunable white from 2700K to 6500K, saved scenes and music sync. At 9W it puts out 600 lumens through a 110° beam with a CRI of 80+, and the 1-inch profile with included junction box drops into a 4-inch cutout, IC rated for direct contact with insulation. The aluminum body is wet-location rated and surge protected to 1 kV, so it holds up in bathrooms, covered exteriors and commercial spaces alike. Dimming is app only, so there is no wall dimmer compatibility to check. cETLus listed and backed by a 5-year warranty.
Slim Panel 6" | RGBW | 1100 Lumens | Round | White | V4
Larger rooms get the same app-controlled colour lighting, with 1100 lumens from a 12W fixture. This 6-inch slim panel works with the Smart Life app, Google Home or Amazon Alexa, giving the end user 16 million colours, tunable white from 2700K to 6500K, saved scenes and music sync from their phone. The 110° beam and CRI of 80+ cover kitchens, living areas and commercial spaces, and the 1-inch profile with included junction box fits a 6-inch cutout, IC rated for direct contact with insulation. An aluminum body, wet-location rating and 1 kV surge protection make it suitable for bathrooms and covered exteriors as well. Dimming is app only, so no wall dimmer is required or supported. cETLus listed and backed by a 5-year warranty.
COB LED Tape Light | 24V | 2700K | 3W/ft | 16 ft Roll | Weatherproof | Dimmable
Built for outdoor and wet locations, this 24V COB LED tape light delivers a continuous, dot-free line of 2700K warm white light along decks, steps, patios, soffits and exterior coves. IP66 silicone encapsulation protects the chips from rain, snow and water jets, and ETL certification keeps inspections simple. Key Specs: 225 lm/ft | 75 lm/W efficacy 3W/ft | 48W total (16 ft roll) 2700K | CRI 90+ 24Vdc input | Dimmable IP66 | Wet locations 146 LEDs/ft | 180° beam angle Min. cut every 2 in. | Max. run 32 ft PCB width: 5/16 in. (8 mm) Operating temp.: -13°F to 140°F (-25°C to 60°C) Rated life: 50,000 hrs | 3-year warranty Included: 1x COB LED roll (16 ft) 10x mounting brackets 2x solderless 2-wire connectors Power supply and dimmer sold separately.
COB LED Tape Light | 24V | 3000K | 3W/ft | 16 ft Roll | Weatherproof | Dimmable
Built for outdoor and wet locations, this 24V COB LED tape light delivers a continuous, dot-free line of 3000K soft white light along decks, steps, patios, soffits and exterior coves. IP66 silicone encapsulation protects the chips from rain, snow and water jets, and ETL certification keeps inspections simple. Key Specs: 240 lm/ft | 80 lm/W efficacy 3W/ft | 48W total (16 ft roll) 3000K | CRI 90+ 24Vdc input | Dimmable IP66 | Wet locations 146 LEDs/ft | 180° beam angle Min. cut every 2 in. | Max. run 32 ft PCB width: 5/16 in. (8 mm) Operating temp.: -13°F to 140°F (-25°C to 60°C) Rated life: 50,000 hrs | 3-year warranty Included: 1x COB LED roll (16 ft) 10x mounting brackets 2x solderless 2-wire connectors Power supply and dimmer sold separately.
COB LED Tape Light | 24V | 4000K | 3W/ft | 16 ft Roll | Weatherproof | Dimmable
Built for outdoor and wet locations, this 24V COB LED tape light delivers a continuous, dot-free line of 4000K neutral white light along decks, steps, patios, soffits and exterior coves. IP66 silicone encapsulation protects the chips from rain, snow and water jets, and ETL certification keeps inspections simple. Key Specs: 255 lm/ft | 85 lm/W efficacy 3W/ft | 48W total (16 ft roll) 4000K | CRI 90+ 24Vdc input | Dimmable IP66 | Wet locations 146 LEDs/ft | 180° beam angle Min. cut every 2 in. | Max. run 32 ft PCB width: 5/16 in. (8 mm) Operating temp.: -13°F to 140°F (-25°C to 60°C) Rated life: 50,000 hrs | 3-year warranty Included: 1x COB LED roll (16 ft) 10x mounting brackets 2x solderless 2-wire connectors Power supply and dimmer sold separately.
LED Tape Light | 24V | 2700K-5000K Tunable | 4.5W/ft | 16 ft Roll | Weatherproof | Dimmable
This 24V weatherproof LED tape light offers tunable white from 2700K to 5000K, controlled by remote or fixed via CW/WW wiring. Rated IP67 for outdoor and wet-location use. Ideal for façade accents, soffits, deck lighting, garden paths, and architectural coves where color temperature flexibility matters. Rated cULus, compatible with Arani aluminum extrusion profiles. Key Specs: 200 lm/ft │ 80 lm/W efficacy 4.5W/ft │ 72W total (16 ft roll) 2700K-5000K tunable │ CRI 90+ 24Vdc input │ Dimmable IP67 │ Wet locations Min. cut every 2 in. │ Max. run 32 ft LED density: 72 LEDs/ft │ Beam angle: 120° Operating temp: -20°C to 60°C Rated life: 50,000 hrs │ 3-year warranty Included in the box: 1x LED roll (16 ft) 10x mounting brackets 2x solderless 2-wire connectors 4x end caps Power supply and remote sold separately.
COB LED Tape Light | 24V | RGB | 4.5W/ft | 16 ft Roll | Weatherproof
Built for outdoor and wet locations, this 24V RGB COB LED tape light produces seamless, dot-free colour along facades, decks, signage and exterior coves. With 160 LEDs per foot under IP66 silicone encapsulation, colours blend evenly with no visible hot spots, and ETL certification keeps inspections simple. Key Specs: 4.5W/ft | 72W total (16 ft roll) RGB | 4-pin 24Vdc input IP66 | Wet locations 160 LEDs/ft | 180° beam angle Min. cut every 2 in. | Max. run 32 ft PCB width: 3/8 in. (10 mm) Operating temp.: -13°F to 140°F (-25°C to 60°C) Rated life: 50,000 hrs | 3-year warranty Included: 1x RGB COB LED roll (16 ft) 1x RGB strip-to-wire connector (STR-C-COB-RGB-SW-2W) 1x RGB strip-to-strip connector (STR-C-4PIN-RGB) 10x mounting brackets Power supply and RGB controller sold separately.
LED tape light | 24V | 2700K-5000K tunable | 4.5W/ft | Weatherproof | Dimmable | By inch
This 24V weatherproof LED tape light is sold by the inch, making it ideal for custom-length outdoor projects. Offers tunable white from 2700K to 5000K, controlled by remote or fixed via CW/WW wiring. Rated IP67 for wet-location use, with an adhesive backing for tool-free surface mounting. Compatible with Arani aluminum extrusion profiles. Rated cULus. Key Specs: 200 lm/ft │ 80 lm/W efficacy 4.5W/ft │ 72W total (16 ft roll) 2700K-5000K tunable │ CRI 90+ 24Vdc input │ Dimmable IP67 │ Wet locations Min. cut every 2 in. │ Max. run 32 ft LED density: 72 LEDs/ft │ Beam angle: 120° Operating temp: -20°C to 60°C Rated life: 50,000 hrs │ 3-year warranty Power supply and remote sold separately. Sold by the inch.
RGB COB Strip-to-Wire Connector Kit | 10mm LED Strips
Cutting a pre-wired roll to length leaves one piece without leads. This solderless kit fixes that: it lands a cut 10 mm, 4-pin RGB COB section on a pre-wired 7 in lead, so the offcut becomes a second, independent run fed from the controller. The kit includes a connection platform, an end cap that locks the strip in place, and the strip-to-wire connector, all matched to Arani's 24V RGB COB strip. All four conductors land in a single clamp, with no splice to tape up or troubleshoot later. One roll can now cover two separate zones, and nothing ends up in the bin.
RGB COB Strip-to-Strip Connector Kit | 10mm LED Strips
A pre-wired 16 ft roll covers most jobs, but not every run lands on a roll length. This solderless kit joins two 10 mm, 4-pin RGB COB segments end to end, so you can add an offcut or a second cut section and extend the run exactly where the layout needs it. Two end caps lock each strip onto a shared connection platform, keeping all four channels aligned so colour stays consistent across the joint. Cut at any 2 in mark, clamp, and keep going, with no soldering on site. Matched to Arani's 24V RGB COB strip, it turns leftover tape into usable run length instead of scrap.
Circular 12" Ceiling Light | White | 5CCT Variable | 20-22-24W 2520 Lumens | V5
The 12-inch slim LED downlight delivers up to 2520 lumens at 105 lm/W, sized for living rooms, larger bedrooms, and open kitchens. Five color temperatures (2700K, 3000K, 3500K, 4000K, 5000K) and three power levels (20W, 22W, 24W) are selected on the fixture, so one stocked unit replaces multiple SKUs. The 11/16-inch profile, plastic body, and polycarbonate lens make this a clean fit for slab and joist ceilings without recessing. CRI of 90+ and a 110° beam keep light quality consistent at residential ceiling heights. Triac dimming, 1 kV surge protection on both L-N and L/N-PE, and damp-location rating cover most indoor applications including covered porches and bathrooms. cETLus listed under file 5000999, backed by a 5-year warranty and 35,000-hour rated life.
Circular 7" Ceiling Light | White | 5CCT Variable | 8-10-12W 1000 Lumens | V5
The 7-inch slim LED downlight gives electricians a single SKU that covers most low-profile ceiling jobs. Five color temperatures (2700K, 3000K, 3500K, 4000K, 5000K) and three power levels (8W, 10W, 12W) are selectable directly on the fixture, so one stocked unit replaces five. Output ranges from 800 to 1000 lumens at 80 lm/W with a 90+ CRI and a 110° beam, suitable for kitchens, hallways, and laundry rooms. The 11/16-inch profile, plastic body, and polycarbonate lens keep installation clean in tight ceiling cavities. Triac dimming, 1 kV surge protection on both L-N and L/N-PE, and damp-location rating cover most residential and light commercial use cases. cETLus listed, backed by a 5-year warranty and 35,000-hour rated life.
Disconnects & Safety Switches
AC Disconnect | 60A | Non-Fused
Fast, clean power isolation at the condenser starts with the right disconnect — one that won't send you hunting for fuse cartridges mid-job. The ACD60A handles isolation through the pull-out mechanism alone, relying on the panel breaker for overcurrent protection, exactly as NEC Article 440 intends for this application. The Type 3R galvanized steel enclosure is rated for wet locations, so it stands up to whatever the outdoor install throws at it — rain, sleet, and direct exposure — without compromise. Six knockouts in ½", ¾", and 1" sizes give you the conduit entry flexibility to land the job cleanly regardless of your approach. Rated for both residential and light commercial work, and cULus listed to keep inspectors satisfied.
Boxes, Covers and Extensions
2004-LH - Large Device Box with NMD Clamps 18.5 cu. in
Arani Branded, built for Canadian electricians and contractors. Bulky thermostats and low-voltage controls finally get the room they need. This extra-deep galvanized steel device box delivers 18.5 cubic inches of usable volume in a non-gangable single-gang design, so crowded conductors and oversized devices seat cleanly without a fight. Integrated clamps for nonmetallic sheathed cable let you land wire without add-on connectors, and the nail-on design drives straight into wood studs during new-work rough-in. cETL certification keeps inspections moving. On thermostat and device drops where standard-depth boxes come up short, it means a faster, cleaner install.
MBD-1K - Deep Box for Concrete with Knockouts 21 cu. in
Arani Branded, built for Canadian electricians and contractors. Rough-in through concrete and block gets far simpler with a box built for the job. Galvanized steel stands up to the pressure of a masonry pour while 21 cubic inches of depth leaves ample room for conductors and connections. Fourteen concentric knockouts accept 1/2, 3/4 and 1 inch conduit, so feeds land from whatever angle the wall allows without hunting for the right entry. The single-gang body sets devices flush in poured or block walls, and cETL certification backs the install at inspection. It is the difference between fighting a shallow box in masonry and dropping in one that fits the first time.
OBEX - Octagonal Extension for Drywall 5 cu.in
Arani Branded, built for Canadian electricians and contractors. A 4-inch octagon box set too deep behind drywall becomes a code problem fast, and this shallow galvanized steel extender solves it without opening the wall. It brings the recessed box flush with the finished surface so devices and fixtures mount square and the gap that inspectors flag disappears. At half an inch deep it adds just enough reach without stealing device room, and it fastens straight to the existing box in seconds. cETL certification confirms the fix meets code. For a recessed box discovered after the drywall is up, it is the quickest path back to a compliant, finished install.
55171-K - Octagonal Extension Ring 21 cu.in
Arani Branded, built for Canadian electricians and contractors. Running out of room in an existing 4-inch octagon box no longer means tearing it out. This deep galvanized steel extension ring stacks directly on top and adds 21 cubic inches of usable volume for extra conductors, splices or a fixture change. Concentric 1/2 and 3/4 inch knockouts open only the entries you need, and the steel body seats cleanly on the box below. cETL certification keeps the addition inspection-ready. When a box is overfilled and a device still has to go in, it turns a rework headache into a two-minute fix.
53151-SUB-K - Extension for 4’’ Square Box 1 1/2’’ Deep 21 cu.in
Arani Branded. Arani Exclusive. When a device box runs out of room, this adapter ring converts it to a full 4 in square without pulling the box or the existing wiring. At 1-1/2 in deep, it adds 21 cu in (344 ml) of fill, enough for up to 14 #14 AWG or 12 #12 AWG conductors. Eight 1/2 in and four 3/4 in knockouts open up options for new conduit runs, and combination Robertson/slotted screws work with the square bit already in your driver. The galvanized steel body (1.2 mm min.) is cULus listed for residential, commercial and industrial work. Add capacity and conduit access in minutes while keeping the original install in place.
8362 - 1 Gang 4’’ Square Receptacle Box Cover 4.6 cu.in
Turning a 4x4 square box into a finished single-device outlet takes one part with this galvanized steel cover. It centers a decorator-style opening over the box so a switch, receptacle or GFCI mounts square and sits flush behind the wall plate. The rugged steel holds its shape and keeps the opening square for a clean, gap-free finish. cETL certification keeps the assembly inspection-ready. On any 4x4 rough-in that needs a single decorator device, it is the fast, tidy way to close it out.
8369 - 2 Gang 4’’ Square Receptacle Box Cover 4.6 cu.in
Two decorator-style devices can share a single 4x4 box when this galvanized steel cover does the adapting. It positions a pair of decorator openings side by side so switches, receptacles or a switch-and-GFCI combo mount square and finish flush under the plate. Rugged steel keeps both openings aligned for a gap-free look. cETL certification backs the install at inspection. Where a 4x4 has to serve two decorator devices, it closes out the opening in one clean step.
Tools
Adjustable Tongue-And-Groove Pliers | 10"
Our 10" adjustable groove joint pliers are designed for high-performance gripping and fastening in plumbing, mechanical, and industrial applications. Made in Germany and manufactured from special chrome vanadium steel with a grey atramentized finish, they deliver strength, durability, and corrosion resistance. The push-button adjustment mechanism allows fast, precise positioning directly on the workpiece. With 25 adjustment positions, the pliers provide flexible, secure fitment with no risk of unintentional shifting. An optimized serration pattern positioned near the joint ensures exceptional grip under heavy load. The precision-engineered jaw design enhances self-locking performance for secure handling of round and flat materials.
Cutting Pliers | 7"
Our 7" diagonal cutting pliers are built for clean, consistent cutting performance in electrical, mechanical, and general-purpose applications. Made in Germany and manufactured from durable carbon steel, they ensure strength and long service life. Designed to cut both soft and hard wire, these pliers deliver reliable performance across a wide range of materials. The ultra-precise cutting edges provide clean, accurate cuts with a rated capacity for hard wire up to Ø 2.5 mm (3/32").
Gripping Pliers | 8"
Our 8" long nose pliers are engineered for precision gripping, bending, and cutting in electrical and industrial applications. Made in Germany and manufactured from special high-grade carbon steel, they provide durability and long-term performance in demanding environments. The slim, straight half-round jaws ensure exceptional reach and precise control, making them ideal for detailed work and confined spaces. The integrated cutter delivers clean, effortless cuts with a rated capacity for hard wire up to Ø 1.8 mm (1/16").
Gripping Pliers | 6-1/4"
Our 6-1/4" long nose pliers are designed for precision gripping, bending, and cutting in electrical, mechanical, and general-purpose applications. Made in Germany and manufactured from high-grade carbon steel, they ensure durability and long service life. The slim, straight half-round jaws provide exceptional reach and accurate control in confined or hard-to-access areas. An integrated cutter delivers clean, effortless cuts with a rated capacity of hard wire up to Ø 1.6 mm (1/16").
Lineman's Pliers | 9"
Our 9" lineman's pliers are engineered for demanding electrical and industrial applications. Made in Germany and manufactured from special high-grade carbon steel, they deliver durability, precision, and long-term performance in heavy-duty environments. The extra-long, ultra-sharp cutting edges are optimized for effortless precision cutting, particularly on flat cables. The aggressive serrated jaws ensure maximum gripping strength, while the integrated 4-point vice-grip pipe feature provides a secure, slip-resistant hold on pipes and round materials. The power-joint design reduces hand effort by up to 30%, increasing efficiency and minimizing fatigue during extended use. An additional gripping zone beneath the joint enhances versatility and control in tight or awkward spaces.